PW0-104 Free Demo Download

Certinside offers free demo for PW0-104 120 Q&As with Expert Real). You can check out the interface, question quality and usability of our practice exams before you decide to get it.



Download PW0-104 dumps Pdf Demo

Download PW0-104 dumps iEngine Demo

Real questions and answers
　
　
Exam : CWNP PW0-104
Title : Wireless LAN Administration Exam

1. Given: Return Loss is the decrease of forward energy in a system because some of the power is being reflected back toward the transmitter.
What can cause a high return loss in an RF transmission system?
A. A Voltage Standing Wave Ratio (VSWR) of 1.5:1
B. An impedance mismatch between devices in the RF system
C. Cross-polarization of the RF signal as it passes through the RF system
D. The use of multiple connector types in the RF system (e.g. N-type and SMA-type)
E. Low output power at the transmitter and use of a high-gain antenna
Answer: B

2. What factor is NOT taken into account when calculating the System Operating Margin of a point-to-point outdoor WLAN bridge link?
A. Operating frequency
B. Tx antenna gain
C. Tx power
D. Rx cable loss
E. Antenna height
F. Rx sensitivity
G. Distance
Answer: E

3. Given: A WLAN transmitter that emits a 200 mW signal is connected to a cable with a 9 dB loss.
if the cable is connected to an antenna with a 10 dBi gain, what is the EIRP at the antenna element?
A. 50 mW
B. 250 mW
C. 500 mW
D. 750 mW
E. 1000 mW
Answer: B

4. What word describes the bending of an RF signal as it passes between mediums of different density?
A. Diffraction
B. Reflection
C. Refraction
D. Diffusion
E. Scattering
Answer: C

5. What factors affect the distance that an RF signal can be effectively received?
A. Transmitting station’s antenna type
B. Receiving station’s radio sensitivity
C. Fresnel zone blockage
D. Power over Ethernet (PoE) usage
E. Antenna connector type
F. Distance between access points
Answer: ABC

6. As an RF wave propagates through space, the wave front experiences natural expansion. What is the detrimental effect of this expansion in a WLAN system?
A. Linear Diffusion Loss
B. Signal Attenuation
C. Transmission Obfuscation
D. Fresnel Zone Thinning
E. Azimuth Inflation
Answer: B

7. What causes an excessively high Voltage Standing Wave Ratio (VSWR) in an 802.11 WLAN?
A. An impedance mismatch between devices in series with the main RF signal
B. Reflected DC voltage on the main RF signal line
C. Refracted RF signal peaks along the main signal path
D. Crosstalk (inductance) between adjacent conductors
Answer: A

8. Given: ABC Company’s network administrator was just asked to install a 5 GHz OFDM bridge link between two buildings. He connected a WLAN bridge with a 50-ohm output to a 50-ohm RF coaxial cable. He connected the other end of the RF coaxial cable to a 25-ohm, 6 dBi Yagi antenna.
What is the maximum VSWR between the WLAN bridge and the Yagi antenna?
A. 1.0:1
B. 1.1:1
C. 1.2:1
D. 1.5:1
E. 2.0:1
F. 1.0:2
Answer: E

PW0-300 Free Demo Download

Certinside offers free demo for PW0-300 140 Q&As with Expert Real). You can check out the interface, question quality and usability of our practice exams before you decide to get it.



Download PW0-300 dumps Pdf Demo

Download PW0-300 dumps iEngine Demo

Real questions and answers
　
　
Exam : CENP PW0-300
Title : Certified Wireless Network Expert

1. According to the IEEE 802.11 standard (as amended), transmit power information is carried in which frames?
A. TPC Report frame
B. ADDTS Response frame
C. Probe Response frame
D. Beacon frame
E. Channel Switch Announcement frame
F. Measurement Report frame
Answer: ACD

2. When using a protocol analyzer to capture conversations over a WLAN, you may often encounter encrypted data frames. Most WLAN protocol analyzers have a feature that allows the analyst to save and reload the captured frames into memory at a later time. Using this functionality, what task can be performed?
A. When IEEE 802.1X/LEAP is being used as the WLAN security mechanism, the authentication response frame can be replayed from a saved trace file at a later time to successfully authenticate a hacker.
B. If a user name and password for an IEEE 802.1X/EAP-TTLS security implementation can be obtained through social engineering tactics, the user name and password can be entered into the analyzer to decrypt the frames from a saved trace file.
C. An analyst can search through the captured frames looking for RADIUS frames that will disclose the user’s password.
D. Encrypted frames may be decrypted offline, after they are captured, by entering a WEP key or WPA passphrase into the analyzer.
Answer: D

3. 1D Frame Precedence Values
B. GRE Priority Bits
C. IEEE 802.1Q Tag Protocol Identifiers
D. IP Differentiated Services Code Points
E. QoS Control Header Values
Answer: D
2. Given: An ingress frame arrives on the Ethernet port of an autonomous AP marked with an IEEE 802.1D user priority value.
Which IEEE 802.1D user priority values (by name) will assure the data payload carried by the Ethernet frame gets assigned to the highest priority WMM queue?
A. Controlled Load
B. Network Control
C. Video
D. Voice
E. Best Effort
F. Excellent Effort
Answer: BD

4. How long, in microseconds, is the required Slot Time announced by an AP in an ERP BSS when both HR-DSSS and ERP-OFDM client stations are associated to the AP?
A. 2
B. 4
C. 9
D. 10
E. 20
Answer: E

5. In a Split MAC wireless network architecture, lightweight APs map user priorities (UPs) specified by the QoS STA on incoming frames to ___________.
A. IEEE 802.1D Frame Precedence Values
B. GRE Priority Bits
C. IEEE 802.1Q Tag Protocol Identifiers
D. IP Differentiated Services Code Points
E. QoS Control Header Values
Answer: D

6. A QoS STA obtains a TXOP for an access category (AC) after what two parameters are met?
A. After a scheduled service period ends
B. The medium is idle at the AIFS[AC] slot boundary
C. The backoff time for that AC has expired
D. After a Block ACK Response
E. After a Target Beacon Transmission Time (TBTT)
Answer: BC

7. Given: When the delayed Block Ack policy is used between two QoS STAs, the recipient must respond to a BlockAckReq frame with an ACK frame. The recipient must then send its BlockAck response frame in a subsequently obtained TXOP.
Once the contents of the BlockAck frame have been prepared, the recipient must _______________.
A. Send the BlockAck response frame to the originator in the earliest possible TXOP using the highest priority AC.
B. Send an ATIM to the originator signifying that the BlockAck response frame is ready for transmission.
C. Include the TID of the BlockAckReq in the next TXOP Request to the HC.
D. Wait for one PIFS after the next Beacon and transmit the BlockAck response to the originator using the same AC as the BlockAckReq frame.
Answer: A

8. The IEEE 802.11 standard allows for frame fragmentation. Which two fields in the IEEE 802.11 frame are involved in numbering data frame fragments and notifying the receiving station when all of the fragments of a data frame have been received?
A. Capability Information field
B. Frame Control field
C. ERP Information field
D. Sequence Control field
E. DS Parameter field
F. Ordered Service field
Answer: BD

PW0-200 Free Demo Download

Certinside offers free demo for PW0-200 120 Q&As with Expert Real). You can check out the interface, question quality and usability of our practice exams before you decide to get it.



Download PW0-200 dumps Pdf Demo

Download PW0-200 dumps iEngine Demo

Real questions and answers
　
　
Exam : CENP PW0-200
Title : Certified Wireless Security Professional(CWSP)

1.
C. Require VPN software for connectivity to the corporate network.
D. Require WPA2-Enterprise as the minimal WLAN security solution.
E. Require Port Address Translation (PAT) on each laptop.
F. Require a managed wireless endpoint security agent on each laptop.
Answer: ABCF
2. Given: You have a laptop computer with an integrated Wi-Fi compliant MiniPCI card.
What statements describe the limited effectiveness of locating rogue access points using WLAN discovery software such as NetStumblerKismetor MacStumbler?
A. Discovery tools like those listed cannot determine the authorization status of an access point.
B. A laptop computer can only be in one location at a time.
C. Discovery tools like those listed cannot determine if an access point is attached to a wired network.
D. Rogue access points using non-IEEE 802.11 frequency bands or unpopular modulations are not detected.
E. When data encryption in useaccess points cannot be detected using discovery tools like those listed.
Answer: ABCD

2. What policies would prevent peer-to-peer attacks against wireless-enabled corporate laptop computers when the laptops are also used on public access networks such as wireless hotspots?
A. Require managed personal firewall software on each laptop.
B. Require secure applications such as POP3/SHTTPSand SSH2.
C. Require VPN software for connectivity to the corporate network.
D. Require WPA2-Enterprise as the minimal WLAN security solution.
E. Require Port Address Translation (PAT) on each laptop.
F. Require a managed wireless endpoint security agent on each laptop.
Answer: ABCF

3. Given: ABC Company has a WLAN controller with three access points15 client devicesand uses WPA2-Personal for WLAN security.
What statement about ABC Company’s WLAN security is true?
A. Intruders may obtain the passphrase with an offline dictionary attack and gain network accessbut will be unable to decrypt data traffic.
B. Traffic injection attacks are possible because the transmitter lacks frame numbering.
C. An unauthorized wireless client device cannot associatebut can eavesdrop on some data because WPA2-Personal does not encrypt broadcast traffic.
D. An authorized WLAN user with a protocol analyzer can decode data frames of other authorized users if he captures that user’s 4-Way Handshake.
E. Because WPA2-Personal uses Open System authentication followed by a 4-Way Handshakehijacking attacks are easily performed.
Answer: D

4. Given: John Smith often works from home and wireless hotspots rather than commuting to the office. His laptop connects to the office network over IEEE 802.11 WLANs.
To safeguard his datawhat wireless security policy items should be implemented?
A. Use an IPSec VPN for remote connectivity
B. Use an HTTPS captive portal for authentication at hotspots
C. Use personal firewall software on his laptop
D. Use a protocol analyzer on his laptop to monitor for risks
E. Use 802.1X/PEAPv0 to connect to the corporate office network
Answer: AC

5. What WIPS parameter is configured to generate notifications?
A. Mobile unit density violations
B. Admission control status
C. Sensor sensitivity levels
D. Policy threshold values
Answer: D

6. In this diagram illustrating an example of the IEEE 802.11 standard’s 4-Way Handshakewhat is the purpose of the ANonce and SNonce?
A. They are used to pad Message 1 and Message 2 so there is no empty space in the frame.
B. The IEEE 802.11 standard requires that all cryptographic frames contain a nonce for security purposes.
C. They are added together and used as the GMKfrom which the GTK is derived.
D. They are values used in the derivation of the Pairwise Transient Key.
Answer: D

7. What happens in a bit flipping attack against an IEEE 802.11 device?
A. An attacker captures an encrypted framemodifies the ciphertextmodifies the ICV to hide the change to the ciphertextand then transmits the frame to appear as if it is from the original source.
B. An attacker uses a non-linear Message Integrity Check (MIC) on his computer to form a wireless crossover connection with the target computer.
C. An attacker injects data into a wireless transmission that results in a memory access exception at the target system for the purpose of breaching security.
D. An attacker sends each frame with the first bit alternating between 0 and 1causing the target computer to disable encryption synchronization.
E. An attacker captures an encrypted authentication frameand then executes a cracking algorithm against each 0 and 1 in the frame. After the frame is crackedit is used to authenticate the attacker’s computer.
Answer: A

8. Given: A network security auditor is assessing an IEEE 802.11 network’s exposure to security holes.
What task would save the most time if performed before the audit?
A. Identify the IP subnet information for each network segment.
B. Identify the manufacturer of the wireless intrusion prevention system.
C. Identify the skill level of the wireless network security administrator(s).
D. Identify the manufacturer of the wireless infrastructure hardware.
E. Identify the wireless security solution(s) currently in use.
Answer: E

PW0-205 Free Demo Download

Certinside offers free demo for PW0-205 120 Q&As with Expert Real). You can check out the interface, question quality and usability of our practice exams before you decide to get it.



Download PW0-205 dumps Pdf Demo

Download PW0-205 dumps iEngine Demo

Real questions and answers
　
　
Exam : CENP PW0-205
Title : certified wireless analusis professional(cwap)

1. Which of the following descriptions accurately describes IEEE 802.11 compliant Power Save mode operation in a DCF Basic Service Set?
A. Following a period of time in a low power state, client stations wake themselves and automatically poll the access point for traffic using a PS-Poll frame.
B. When the access point’s buffer is full, the access point wakes all client stations using a PS-Poll frame so that they can receive the data.
C. Upon receiving traffic for a dozing station, the access point wakes the client station using a PS-Poll frame so that the client station can receive the data.
D. After waking from a low power state, client stations listen for the next beacon to determine if sending a PS-Poll frame to the access point is necessary.
E. After waking at a schedule TBTT, client stations automatically send Null Function frames to the access point with the Power Management bit cleared.
Answer: D

2. A wireless network administrator has examined the frame retry counts on several client stations in a WLAN that is not using encryption, and has determined that they are extraordinarily high. For this reason, he has decided to configure station fragmentation thresholds to 400 bytes. With this configuration change, when a data frame with a 1500 byte MSDU is transmitted by one of the wireless client stations to a wired station through an access point, what will be the order and size (in bytes) of the fragments as they’re transmitted?
A. Frame1 = 400, Frame2 = 400, Frame3 = 400, Frame4 = 300
B. Frame1 = 300, Frame2 = 300, Frame3 = 300, Frame4 = 300, Frame5 = 300
C. Frame1 = 300, Frame2 = 400, Frame3 = 400, Frame4 = 400
D. Frame1 = 400, Frame2 = 400, Frame3 = 400, Frame4 = 400, Frame5 = 40
E. The fragmentation threshold setting on client stations only affects received frames, not transmitted frames
F. The fragmentation threshold setting on client stations is not a manual adjustment, and can only be auto-configured by access points
Answer: D

3. Which of the following is true regarding frame acknowledgement in an 802.11 wireless LAN?
A. ACK frames following Data fragments set the NAV of competing stations for a duration equal to two SIFS plus the next Data fragment and its ACK.
B. A client station reassociation request frames are only acknowledged with a reassociation response from the access point when roaming in a wireless LAN secured with 802.1X/EAP.
C. Probe request acknowledgement (sending of a probe response) is configurable in the access point and is always linked to SSID broadcast configuration in Beacons.
D. Beacon frames are acknowledged by all client stations configured for PCF mode.
E. Frame fragments are acknowledged individually (with an ACK frame)
F. In PCF mode, WEP-Data frames are only acknowledged by client stations, never by access points.
Answer: AE

4. Choose the true statements regarding wireless network discovery processes for an 802.11b network.
A. Client stations may continually send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner, regardless of their association state.
B. Access points send Beacon Management frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner including the channel for which the access point is configured.
C. Client stations send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner until they associate with an access point. After associating to an access point, they are no longer allowed to transmit Probe Request frames.
D. Access points send Beacon Management frames only on the 802.11b channel in the 2.4 GHz ISM band for which the access point is configured.
E. Client stations send Probe Request frames on all 802.11b channels in the 2.4 GHz ISM band in a consecutive manner until they receive at least 3 Probe Response frames.
Answer: AD

5. When an access point sends an RTS frame, the duration field will contain an amount of time, measured in microseconds, equal to which of the following?
A. 2 ACK, 1 RTS, 1 DATA, 4 SIFS
B. 1 ACK, 1 CTS, 1 DATA, 3 SIFS
C. 1 DATA, 1 RTS, 2 SIFS, 1 DIFS, 1 ACK
D. 1 RTS, 1 CTS, 1 DATA, 2 ACK, 4 SIFS
Answer: B

6. 11 compliant Power Save mode operation in a DCF Basic Service Set?
A. Following a period of time in a low power state, client stations wake themselves and automatically poll the access point for traffic using a PS-Poll frame.
B. When the access point’s buffer is full, the access point wakes all client stations using a PS-Poll frame so that they can receive the data.
C. Upon receiving traffic for a dozing station, the access point wakes the client station using a PS-Poll frame so that the client station can receive the data.
D. After waking from a low power state, client stations listen for the next beacon to determine if sending a PS-Poll frame to the access point is necessary.
E. After waking at a schedule TBTT, client stations automatically send Null Function frames to the access point with the Power Management bit cleared.
Answer: D
2. The Timestamp field, found in 802.11 Beacon Management frames, is 8 bytes in length and serves which of the following purposes?
A. Keeps all client stations in a BSS synchronized to within approximately 4 microseconds of the access point.
B. Allows client stations in the IBSS to pick the best of multiple beacons.
C. Used to notify client stations using power management features of how long their queued frames have been held by the access point.
D. Informs associating client stations how often to expect Beacon Management frames to be sent by the access point.
E. Allows all client stations in a BSS to calculate how long it took for the Beacon Management frame to traverse the wireless medium.
Answer: AB

7. Which is true of the Association Identifier (AID) used in 802.11 wireless LANs?
A. The AID has a maximum value of 2048, and is used to uniquely identify a wireless client station associated with an access point.
B. The AID has a maximum value of 2007, and resides in the duration/ID field of a PS-Poll frame only.
C. When bit 16 of the field is zero, the value in bits 15-0 represent the remaining duration of a frame exchange.
D. The least significant 8 bits of this field are used by the wireless client station to identify which bit in a TIM indicates that the access point has frames buffered for the wireless client station.
E. The AID is used by the access point in DCF mode to reduce duplicate transmissions when sending multicasts.
Answer: B

8. An 802.11b client station, sends a single 600 byte MSDU to another 802.11b client station while operating as part of an unsecured infrastructure BSS. Due to thresholds set on all client stations and the access point, all MPDUs over 300 bytes in length invoke the RTS/CTS protocol. How many individual CTS frames are transmitted on the wireless medium as part of the entire process of moving the 600 byte MSDU between the two client stations?
A. 1
B. 2
C. 3
D. 4
Answer: B

PW0-050 Free Demo Download

Certinside offers free demo for PW0-050 180 Q&As with Expert Real). You can check out the interface, question quality and usability of our practice exams before you decide to get it.



Download PW0-050 dumps Pdf Demo

Download PW0-050 dumps iEngine Demo

Real questions and answers
　
　
Exam : CENP PW0-050
Title : Wireless#

1. In an 802.11 wireless LAN, what term is used to describe the wireless network name?
A. BSSID
B. ATIM
C. DIFS
D. SSID
E. FHSS
Answer: D

2. Bluetooth devices use which spread spectrum technology?
A. Frequency Hopping Spread Spectrum (FHSS)
B. Direct Sequence Spread Spectrum (DSSS)
C. Orthogonal Frequency Division Multiplexing (OFDM)
D. Infrared Spread Spectrum (ISS)
Answer: A

3. The 802.16-2004 standard, supported by the WiMAX interoperability initiative, supports which features?
A. Client mobility
B. 802.16e compatibility
C. Quality of Service (QoS)
D. Strong security
E. Ad Hoc client networking
Answer: CD

4. Which wireless data technology would have its data rate most negatively impacted by bright sunlight?
A. WiMAX
B. MIMO
C. Bluetooth
D. Wi-Fi
E. Infrared
Answer: E

5. 2 Kbps
D. 1.152 Mbps
E. 4 Mbps
Answer: C
3. A ZigBee network can scale to how many nodes?
A. 2,000
B. 10,000
C. 42,000
D. 65,000
E. 78,000
Answer: D
4. Which wireless data technology would have its data rate most negatively impacted by bright sunlight?
A. WiMAX
B. MIMO
C. Bluetooth
D. Wi-Fi
E. Infrared
Answer: E
5. Which wireless technology supports both line-of-sight (LoS) and non-LoS connectivity?
A. ZigBee
B. WiMAX
C. Wi-Fi
D. Infrared
E. Bluetooth
Answer: B

6. 6 Kbps
C. 115.2 Kbps
D. 1.152 Mbps
E. 4 Mbps
Answer: C
3. A ZigBee network can scale to how many nodes?
A. 2,000
B. 10,000
C. 42,000
D. 65,000
E. 78,000
Answer: D
4. Which wireless data technology would have its data rate most negatively impacted by bright sunlight?
A. WiMAX
B. MIMO
C. Bluetooth
D. Wi-Fi
E. Infrared
Answer: E
5. Which wireless technology supports both line-of-sight (LoS) and non-LoS connectivity?
A. ZigBee
B. WiMAX
C. Wi-Fi
D. Infrared
E. Bluetooth
Answer: B
6. The 802.16-2004 standard, supported by the WiMAX interoperability initiative, supports which features?
A. Client mobility
B. 802.16e compatibility
C. Quality of Service (QoS)
D. Strong security
E. Ad Hoc client networking
Answer: CD
7. 802.11a compliant wireless LAN systems use which frequency bands?
A. 2.4 GHz ISM band
B. 5.2 GHz U-NII band
C. 5.3 GHz U-NII band
D. 900 MHz ISM band
E. 5.7 GHz ISM band
Answer: BC

7. A ZigBee network can scale to how many nodes?
A. 2,000
B. 10,000
C. 42,000
D. 65,000
E. 78,000
Answer: D

8. 11 wireless LAN, what term is used to describe the wireless network name?
A. BSSID
B. ATIM
C. DIFS
D. SSID
E. FHSS
Answer: D
2. What is the maximum speed of IrDA compliant serial infrared (SIR)?
A. 19.2 Kbps
B. 57.6 Kbps
C. 115.2 Kbps
D. 1.152 Mbps
E. 4 Mbps
Answer: C

PW0-100 Free Demo Download

Certinside offers free demo for PW0-100 120 Q&As with Expert Real). You can check out the interface, question quality and usability of our practice exams before you decide to get it.



Download PW0-100 dumps Pdf Demo

Download PW0-100 dumps iEngine Demo

Real questions and answers
　
　
Exam : CENP PW0-100
Title : certified wireless network administrator(cwna)

1. Given: ABC University provides wireless access to campus buildings from their Data Center building. ABC has installed a tower on the Data Center building with a sectorized omnidirectional antenna array using 90 of horizontal beamwidth per sector.
What is the next step in configuring the antenna array?
A. Calculate Earth Bulge into the System Operating Margin (SOM).
B. Configuring the downtilt of each antenna in the array.
C. Providing DC power to each antenna in the array.
D. Adjusting each antenna’s beamwidths for optimal gain.
Answer: B

2. While working on a presentation document in a conference room equipped with a wireless network, you notice that, as you turn your laptop in different directions, your wireless signal strength changes. What RF signal property is primarily responsible for this change in signal strength?
A. The RF signal’s amplitude is changing due to a change in the visual line-of-sight.
B. The RF signal’s wavelength is being affected by varying antenna gain.
C. The RF signal’s multipath is changing the amount of RF absorbed by nearby objects.
D. The RF signal’s phase is oscillating due to electromagnetic interference (EMI).
E. The RF signal’s polarization is different than the receiving antenna.
Answer: E

3. In a long-distance RF link, what statement about Fade Margin is true?
A. Fade Margin is the amount of signal strength in addition to the Link Budget.
B. The Fade Margin of a long-distance RF link does not account for antenna gain.
C. Fade Margin is rarely taken into account on a long-distance RF link.
D. Fade Margin and Jamming Margin are synonymous, interchangeable terms.
Answer: A

4. What is a valid type of lightning arrestor used with 802.11 wireless LANs?
A. Coaxial arrestor with a metal oxide varistor (MOV) input circuit
B. Parallel tuned tank-circuit arrestor
C. Coaxial arrestor with a gas discharge tube
D. Inductor-based load-sensing arrestor
Answer: C

5. Given: XYZ Corporation is experiencing connectivity problems with their existing building-to-building bridge link. A brick wall on the roof of one building is partially blocking the Fresnel Zone, and the connection is dropping many frames. The administrator moves the antenna to an area not obstructed by the brick wall and then realizes the RF cable cannot reach the new location.
If an RF extension cable is used, what are the likely results?
A. The data throughput rate will increase because VSWR will decrease.
B. The Equivalent Isotropically Radiated Power (EIRP) will decrease.
C. The antenna coverage area will decrease.
D. The return loss will increase unless the impedance of the RF extension cable is equal to 50% of the antenna impedance.
E. The likelihood of a direct lightning strike will increase, placing the entire WLAN system at risk.
Answer: BC

6. What phrase describes the effect of increasing the distance that an RF wave travels when the RF antenna lobe is focused in a desired direction?
A. Polar Extension
B. Active Amplification
C. Beam Compression
D. Passive Gain
E. Phased Array Propagation
Answer: D

7. What factors affect the propagation distance of an RF signal?
A. Antenna gain
B. Receiving station sensitivity
C. Fresnel zone blockage
D. Power over Ethernet (PoE) usage
E. Antenna polarization
F. Link budget calculations
Answer: AC

8. Which units of measure are used to describe a calculable power quantity?
A. dB
B. dBm
C. dBi
D. mW
E. RSSI
F. dBd
Answer: BD